UltraScape Porcelpoint – Flowable Porcelain Grout, Stone Grey

UltraScape Porcelpoint is a flowable rapid set grout that has been specifically designed for use with porcelain paving & tiles. Porcelpoint is ideal for pointing joints in patios and all types of paving slabs, where an impermeable rigid joint is needed.

Porcelpoint comes in a 20KG tub, in two colours Stone Grey & Limestone, this superior porcelain grout is super fine; even finer in appearance than Flowpoint Fine. Available in joint widths from 2-50mm’s, it is open to pedestrians after just one hour, and cars after four hours. Porcelpoint sets in just 15 minutes, is simple to use, you just add 3.4 litres of water to one 20KG tub.

UltraScape Porcelpoint conforms to the strict demands of BS 7533.

• Unit Size: 20KG Bucket (40 on a full pallet)
• Colours: Stone Grey (also available in Limestone)
• Joint Widths: 2-50mm | Depths: 20mm, up to 200mm in one application
• Open to foot traffic: 1 hour
• Open to vehicular traffic: 4 hours
• Set Time: 15 minutes at 20°C
• Grout designed specifically for porcelain
• Just add water – 3.4 litres per 20KG
• Storage Store in a cool, dry and frost free area at temperatures between 5°C and 30°C
• Yield 11.12 litres approx, per 20kg bucket
• Workability 5-15 minutes
• Shelf life 8 months from the date of manufacture printed on this bucket, unopened. Do not store outside, store inside, off the ground, away from drafts, cold and damp.
• High temperatures and high humidity will reduce shelf life.
• Bond (Adhesion strength) >1.5N/mm² after 28 days
• Compressive strength 49.6N/mm2 after 38 days
• Flexural strength 7.1N/mm² after 28 days
• Tensile strength 3.91N/mm2 after 28 days
• UltraScape Porcelpoint conforms to the strict demands of BS 7533.

UltraScape Porcelpoint Application

UltraScape Porcelpoint has been designed to be a rapid set grout with high fluid consistency, which allows early trafficking, and conforms to the strict demands of BS 7533. Porcelpoint is ideal for patios and paved areas where a rigid or bound void-free joint is required. This superior, fine grade grout is suitable for patios, paths, paved areas, driveways, town centre pedestrian schemes and carriageways. UltraScape Porcelpoint has been designed specifcally for use with porcelain paving slabs, tiles and stone.

UltraScape Porcelpoint Technical Information

UltraScape Porcelpoint is supplied as a pre-mixed dry-pack, which only requires the addition of water on-site. Porcelpoint can fill joints from 2mm to 50mm wide, with a minimum target depth of 20mm, up to 200mm in one application. This highly fluid grout achieves a final compressive strength of 49.6N/mm’ (results achieved using 3.4 litres of water per 20kg bucket), and will reach initial set in 30 minutes. Porcelpoint porcelain paving grout will accept light foot traffic after just one hour, and cars after four hours (dependent upon temperature).

How to Mix & Apply UltraScape Porcelpoint – Flowable Porcelain Grout

Ensure that the paving joints are free from debris and all ponded water has been removed. The paving surface and joints must be pre-misted with water and kept damp until the jointing process has been completed. A 20KG bucket requires 3.4 litres of water and must be mixed for between 3 to 5 minutes until a smooth lump-free consistency has been achieved.

Once mixed, apply Porcelpoint without delay, it must be carefully forced into the joints using a suitable neoprene squeegee. The paving mortar should be constantly moved across the surface to repeatedly top up joints, as the mortar may slump following its initial placement. Use a neoprene squeegee to remove as much mortar as possible from the surface. The surface must be kept constantly damp using a soft spray of water. When the jointing mortar has hardened sufficiently, or achieved its initial set the paving surface must be cleaned using a brush and copious amounts of water. Cleaning must be carried out thoroughly and no mortar must be allowed to remain on the surface of the paving. We recommend an initial washdown to remove the bulk of the grout, and a final wash to remove any residue left over.

How long do I have to use up mixed UltraScape Porcelpoint?

Once mixed, Ultrascape Porcelpoint has approximately 5-15 minutes depending on the outside ambient temperature, to be used up.

UltraScape Porcelpoint Precautions

Please note that a small trial should be done to ensure compatibility with the tiles, paving or stone being used as the manufacturer lnstarmac cannot test all tile/stone types. Wash all tools with clean water frequently. Mix only enough material to apply in 4 minutes, we recommend one bucket at a time. Never remix or add extra water. Wear protective clothing, and avoid skin and eye contact – please note that wet cement can burn the skin.

It is important to remember that cool temperatures can retard, and warm temperatures will accelerate both the workability of the grout and set time. Care should be taken when using the product near drainage. You will need to make sure you have a run-off to take any excess grout away, such as lifting an area of grass, as it must not be allowed to go down a drain and into the watercourse. Ultrascape Porcelpoint is supplied in a bag within a bucket, please check the colour printed on the bag, matches the lid colour before use.

What is UltraScape Porcelpoint – Flowable Porcelain Grout?

UltraScape Porcelpoint is a fluid, rapid-setting flowable porcelain grout that is applied as a wet slurry to quickly point patios, paved areas, terraces and paths. Ideal for both domestic and commercial paving projects,

UltraScape Porcelpoint is supplied as a pre-mixed dry-pack in a bag within a 20KG tub, that just needs the addition of 3.4 litres of water. Porcelpoint fills paving joints from 2 to 50mm’s wide, with a minimum target depth of 20mm, up to 200mm in one application.

Porcelpoint is a really fluid grout that reaches its initial set in just 30 minutes. Porcelpoint porcelain paving grout will accept light foot traffic after just one hour, and cars after four hours (dependent upon temperature).

What is UltraScape Porcelpoint used for?

UltraScape Porcelpoint is a fast set flowable, fine paving grout for grouting patios and paved areas, particularly for porcelain that needs a finer joint. Porcelpoint can accommodate joints from 2 to 50mm’s wide, with a minimum depth of 20mm, up to 200mm in one application. Porcelpoint is ideal for paved areas which are rigid or bound, and where a void-free joint is needed. This rapid set paving grout can be used with all types of natural stone, and porcelain.

Use Porcelpoint alongside the UltraScape BS 7533 Mortar Paving System, a range of high performance materials that meet and exceed the strict demands of BS 7533. Including a rapid strength fine bedding concrete – EcoBed, and paving priming slurry – Pro-Prime.

What colours does UltraScape Porcelpoint come in?

UltraScape Porcelpoint comes in two beautiful colours, Stone Grey & Limestone.

What is the Shelf Life for UltraScape Porcelpoint?

Shelf life from date of manufacture printed on the UltraScape Porcelpoint bucket, unopened in the above conditions, for sealed buckets is 8 months. Please note: the use of this product after the end of the declared storage period may increase the risk of an allergic reaction.

If you’d like to learn a little more about UltraScape Porcelpoint and colours, or for any other questions don’t hesitate to call – ☎️ 0330 122 1025 or 01827 794 350